Synthesis of Well-Ordered Functionalized Silicon Microwires Using Displacement Talbot Lithography for Photocatalysis.

Metal-assisted chemical etching (MACE) is a cheap and scalable method that is commonly used to obtain silicon nano- or microwires but lacks spatial control. Herein, we present a synthesis method for producing vertical and highly periodic silicon microwires, using displacement Talbot lithography before wet etching with MACE. The functionalized periodic silicon microwires show 65% higher PEC performance and 2.3 mA/cm2 higher net photocurrent at 0 V compared to functionalized, randomly distributed microwires obtained by conventional MACE at the same potentials.

Optical Analysis of Perovskite III-V Nanowires Interpenetrated Tandem Solar Cells.

Multi-junction photovoltaics approaches are being explored to mitigate thermalization losses that occur in the absorption of high-energy photons. However, the design of tandem cells faces challenges such as light reflection and parasitic absorption. Nanostructures have emerged as promising solutions due to their anti-reflection properties, which enhances light absorption. III-V nanowires (NWs) solar cells can achieve strong power conversion efficiencies, offering the advantage of potentially integrating tunnel diodes within the same fabrication process. Metal halide perovskites (MHPs) have gained attention for their optoelectronic attributes and cost-effectiveness. Notably, both material classes allow for tunable bandgaps. This study explores the integration of MHPs with III-V NWs solar cells in both two-terminal and three-terminal configurations. Our primary focus lies in the optical analysis of a tandem design using III-V semiconductor nanowire arrays in combination with perovskites, highlighting their potential for tandem applications. The space offered by the compact footprint of NW arrays is used in an interpenetrated tandem structure. We systematically optimize the bottom cell, addressing reflectivity and parasitic absorption, and extend to a full tandem structure, considering experimentally feasible thicknesses. Simulation of a three-terminal structure highlights a potential increase in efficiency, decoupling the operating points of the subcells. The two-terminal analysis underscores the benefits of nanowires in reducing reflection and achieving a higher matched current between the top and the bottom cells. This research provides significant insights into NW tandem solar cell optics, enhancing our understanding of their potential to improve photovoltaic performance.

Composition, Optical Resonances, and Doping of InP/InGaP Nanowires for Tandem Solar Cells: a Micro-Raman Analysis.

We present a micro-Raman study of InP/InGaP tandem junction photovoltaic nanowires. These nanowires render possible InGaP compositions that cannot be made in thin films due to strain. The micro-Raman spectra acquired along the nanowires reveal the existence of compositional changes in the InGaP alloy associated with the doping sequence. The heavily Zn-doped InxGa1-xP (x is the In molar fraction) side of the tunnel diode is Ga rich, x = 0.25, with respect to the n-type and intrinsic segments of the top cell, which are close to the nominal composition of the NWs (x = 0.35). The p-type end segment is still Ga-rich. Electromagnetic resonances are observed in the tunnel diode. The Raman signal arising from the InGaP side of the tunnel diode is significantly enhanced. This enhancement permits the observation of a Raman mode that can be associated with an LO phonon plasmon coupled mode (LOPCM). This mode has not been previously reported in the literature of InGaP, and it permits the Raman characterization of the tunnel diode. The analysis of this mode and its relation to the LO phonon modes of the alloy, InP-like and GaP-like, allows to establish an apparent one-mode behavior for the phonon plasmon coupling. It indicates that hole plasma couples to the GaP-like LO mode. The LOPCMs are modeled using the Lindhard Mermin formalism for the dielectric function.

Fast nanoscale imaging of strain in a multi-segment heterostructured nanowire with 2D Bragg ptychography.

Developing semiconductor devices requires a fast and reliable source of strain information with high spatial resolution and strain sensitivity. This work investigates the strain in an axially heterostructured 180 nm-diameter GaInP nanowire with InP segments of varying lengths down to 9 nm, simultaneously probing both materials. Scanning X-ray diffraction (XRD) is compared with Bragg projection ptychography (BPP), a fast single-projection method. BPP offers a sufficient spatial resolution to reveal fine details within the largest segments, unlike scanning XRD. The spatial resolution affects the quantitative accuracy of the strain maps, where BPP shows much-improved agreement with an elastic 3D finite element model compared with scanning XRD. The sensitivity of BPP to small deviations from the Bragg condition is systematically investigated. The experimental confirmation of the model suggests that the large lattice mismatch of 1.52% is accommodated without defects.

Enhanced LWIR response of InP/InAsP quantum discs-in-nanowire array photodetectors by photogating and ultra-thin ITO contacts.

Here we report on an experimental and theoretical investigation of the long-wavelength infrared (LWIR) photoresponse of photodetectors based on arrays of three million InP nanowires with axially embedded InAsP quantum discs. An ultra-thin top indium tin oxide contact combined with a novel photogating mechanism facilitates an improved LWIR normal incidence sensitivity in contrast to traditional planar quantum well photodetectors. The electronic structure of the quantum discs, including strain and defect-induced photogating effects, and optical transition matrix elements were calculated by an 8-bandk·psimulation along with solving drift-diffusion equations to unravel the physics behind the generation of narrow linewidth intersubband signals observed from the quantum discs.

Vertically Processed GaInP/InP Tandem-Junction Nanowire Solar Cells.

We present vertically processed photovoltaic devices based on GaInP/InP tandem-junction III-V nanowires (NWs), contacting approximately 3 million NWs in parallel for each device. The GaInP and InP subcells as well as the connecting Esaki tunnel diode are all realized within the same NW. By processing GaInP/InP tandem-junction NW solar cells with varying compositions of the top junction GaInP material, we investigate the impact of the GaInP composition on the device performance. External quantum efficiency (EQE) measurements on devices with varying GaInP composition provide insights into the performance of the respective subcells, revealing that the GaInP subcell is current-limiting for all devices. I-V measurements under AM1.5G illumination confirm voltage addition of the subcells, resulting in an open-circuit voltage of up to 1.91 V. However, the short-circuit current density is low, ranging between 0.24 and 3.44 mA/cm2, which leads to a resulting solar conversion efficiency of up to 3.60%. Our work shows a path forward toward high-efficiency NW photovoltaics and identifies critical issues that need improvement.

Processing and characterization of large area InP nanowire photovoltaic devices.

III-V nanowire (NW) photovoltaic devices promise high efficiencies at reduced materials usage. However, research has so far focused on small devices, mostly ≤1 mm2. In this study, the upscaling potential of axial junction InP NW photovoltaic devices is investigated. Device processing was carried out on a full 2″ wafer, with device sizes up to 1 cm2, which is a significant increase from the mm-scale III-V NW photovoltaic devices published previously. The short-circuit current density of the largest 1 cm2devices, in which 460 million NWs are contacted in parallel, is on par with smaller devices. This enables a record power generation of 6.0 mW under AM1.5 G illumination, more than one order of magnitude higher than previous III-V NW photovoltaic devices. On the other hand, the fill factor of the larger devices is lower in comparison with smaller devices, which affects the device efficiency. By use of electroluminescence mapping, resistive losses in the indium tin oxide (ITO) front contact are found to limit the fill factor of the large devices. We use combined light-beam induced current (LBIC) and photoluminescence (PL) mapping as a powerful characterization tool for NW photovoltaic devices. From the LBIC and PL maps, local defects can be identified on the fully processed devices.

Compositional analysis of oxide-embedded III-V nanostructures.

Nanowire growth enables creation of embedded heterostructures, where one material is completely surrounded by another. Through materials-selective post-growth oxidation it is also possible to combine amorphous oxides and crystalline, e.g. III-V materials. Such oxide-embedded structures pose a challenge for compositional characterization through transmission electron microscopy since the materials will overlap in projection. Furthermore, materials electrically isolated by an embedding oxide are more sensitive to electron beam-induced alterations. Methods that can directly isolate the embedded material, preferably at reduced electron doses, will be required in this situation. Here, we analyse the performance of two such techniques-local lattice parameter measurements from high resolution micrographs and bulk plasmon energy measurements from electron energy loss spectra-by applying them to analyse InP-AlInP segments embedded in amorphous aluminium oxide. We demonstrate the complementarity of the two methods, which show an overall excellent agreement. However, in regions with residual strain, which we analyse through molecular dynamics simulations, the two techniques diverge from the true value in opposite directions.

Wafer-Scale Synthesis and Optical Characterization of InP Nanowire Arrays for Solar Cells.

Nanowire solar cells have the potential to reach the same efficiencies as the world-record III-V solar cells while using a fraction of the material. For solar energy harvesting, large-area nanowire solar cells have to be processed. In this work, we demonstrate the synthesis of epitaxial InP nanowire arrays on a 2 inch wafer. We define five array areas with different nanowire diameters on the same wafer. We use a photoluminescence mapper to characterize the sample optically and compare it to a homogeneously exposed reference wafer. Both steady-state and time-resolved photoluminescence maps are used to study the material's quality. From a mapping of reflectance spectra, we simultaneously extract the diameter and length of the nanowires over the full wafer. The extracted knowledge of large-scale nanowire synthesis will be crucial for the upscaling of nanowire-based solar cells, and the demonstrated wafer-scale characterization methods will be central for quality control during manufacturing.

In situpassivation of GaxIn(1-x)P nanowires using radial AlyIn(1-y)P shells grown by MOVPE.

GaxIn(1-x)P nanowires with suitable bandgap (1.35-2.26 eV) ranging from the visible to near-infrared wavelength have great potential in optoelectronic applications. Due to the large surface-to-volume ratio of nanowires, the surface states become a pronounced factor affecting device performance. In this work, we performed a systematic study of GaxIn(1-x)P nanowires' surface passivation, utilizing AlyIn(1-y)P shells grownin situby using a metal-organic vapor phase epitaxy system. Time-resolved photoinduced luminescence and time-resolved THz spectroscopy measurements were performed to study the nanowires' carrier recombination processes. Compared to the bare Ga0.41In0.59P nanowires without shells, the hole and electron lifetime of the nanowires with the Al0.36In0.64P shells are found to be larger by 40 and 1.1 times, respectively, demonstrating effective surface passivation of trap states. When shells with higher Al composition were grown, both lifetimes of free holes and electrons decreased prominently. We attribute the acceleration of PL decay to an increase in the trap states' density due to the formation of defects, including the polycrystalline and oxidized amorphous areas in these samples. Furthermore, in a separate set of samples, we varied the shell thickness. We observed that a certain shell thickness of approximately ∼20 nm is needed for efficient passivation of Ga0.31In0.69P nanowires. The photoconductivity of the sample with a shell thickness of 23 nm decays 10 times slower compared with that of the bare core nanowires. We concluded that both the hole and electron trapping and the overall charge recombination in GaxIn(1-x)P nanowires can be substantially passivated through growing an AlyIn(1-y)P shell with appropriate Al composition and thickness. Therefore, we have developed an effectivein situsurface passivation of GaxIn(1-x)P nanowires by use of AlyIn(1-y)P shells, paving the way to high-performance GaxIn(1-x)P nanowires optoelectronic devices.

Gain and bandwidth of InP nanowire array photodetectors with embedded photogated InAsP quantum discs.

Here we report on the experimental results and advanced self-consistent real device simulations revealing a fundamental insight into the non-linear optical response of n+-i-n+ InP nanowire array photoconductors to selective 980 nm excitation of 20 axially embedded InAsP quantum discs in each nanowire. The optical characteristics are interpreted in terms of a photogating mechanism that results from an electrostatic feedback from trapped charge on the electronic band structure of the nanowires, similar to the gate action in a field-effect transistor. From detailed analyses of the complex charge carrier dynamics in dark and under illumination was concluded that electrons are trapped in two acceptor states, located at 140 and 190 meV below the conduction band edge, at the interface between the nanowires and a radial insulating SiOx cap layer. The non-linear optical response was investigated at length by photocurrent measurements recorded over a wide power range. From these measurements were extracted responsivities of 250 A W-1 (gain 320)@20 nW and 0.20 A W-1 (gain 0.2)@20 mW with a detector bias of 3.5 V, in excellent agreement with the proposed two-trap model. Finally, a small signal optical AC analysis was made both experimentally and theoretically to investigate the influence of the interface traps on the detector bandwidth. While the traps limit the cut-off frequency to around 10 kHz, the maximum operating frequency of the detectors stretches into the MHz region.

Direct Three-Dimensional Imaging of an X-ray Nanofocus Using a Single 60 nm Diameter Nanowire Device.

Nanoscale X-ray detectors could allow higher resolution in imaging and diffraction experiments than established systems but are difficult to design due to the long absorption length of X-rays. Here, we demonstrate X-ray detection in a single nanowire in which the nanowire axis is parallel to the optical axis. In this geometry, X-ray absorption can occur along the nanowire length, while the spatial resolution is limited by the diameter. We use the device to make a high-resolution 3D image of the 88 nm diameter X-ray nanofocus at the Nanomax beamline, MAX IV synchrotron, by scanning the single pixel device in different planes along the optical axis. The images reveal fine details of the beam that are unattainable with established detectors and show good agreement with ptychography.

Implementing an Insect Brain Computational Circuit Using III-V Nanowire Components in a Single Shared Waveguide Optical Network.

Recent developments in photonics include efficient nanoscale optoelectronic components and novel methods for subwavelength light manipulation. Here, we explore the potential offered by such devices as a substrate for neuromorphic computing. We propose an artificial neural network in which the weighted connectivity between nodes is achieved by emitting and receiving overlapping light signals inside a shared quasi 2D waveguide. This decreases the circuit footprint by at least an order of magnitude compared to existing optical solutions. The reception, evaluation, and emission of the optical signals are performed by neuron-like nodes constructed from known, highly efficient III-V nanowire optoelectronics. This minimizes power consumption of the network. To demonstrate the concept, we build a computational model based on an anatomically correct, functioning model of the central-complex navigation circuit of the insect brain. We simulate in detail the optical and electronic parts required to reproduce the connectivity of the central part of this network using previously experimentally derived parameters. The results are used as input in the full model, and we demonstrate that the functionality is preserved. Our approach points to a general method for drastically reducing the footprint and improving power efficiency of optoelectronic neural networks, leveraging the superior speed and energy efficiency of light as a carrier of information.

Photovoltaic nanowires affect human lung cell proliferation under illumination conditions.

Using light to interact with cells is a promising way to steer cell behavior with minimal perturbation. Besides optogenetics, photovoltaic nanostructures such as nanowires can be used to interact with cells using light as a switch. Photovoltaic nanowires have, for instance, been used to stimulate neurons. However, the effects of the photovoltaic activity on cells are still poorly understood and characterized. Here, we investigate the effects of the photovoltaic activity of p-i-n nanowire arrays on A549 human lung adenocarcinoma cells. We have cultured A549 cells on top of vertical arrays of indium phosphide p-i-n nanowires (photovoltaic nanowires), with and without illumination to assess the effects of the nanowire photovoltaic activity on cells. We show that there is a higher proportion of dormant cells when the p-i-n nanowire arrays are illuminated. However, there is no difference in the proportion of dormant cells when the p-i-n nanowires are coated with oxide, which suggests that carrier injection in the cell medium (in this case, the release of electrons from the tip of the nanowires) is an important factor for modulating cell proliferation on photovoltaic nanowires. The results open up for interesting applications of photovoltaic nanowires in biomedicine, such as using them as a dormancy switch.

Hot-carrier separation in heterostructure nanowires observed by electron-beam induced current.

The separation of hot carriers in semiconductors is of interest for applications such as thermovoltaic photodetection and third-generation photovoltaics. Semiconductor nanowires offer several potential advantages for effective hot-carrier separation such as: a high degree of control and flexibility in heterostructure-based band engineering, increased hot-carrier temperatures compared to bulk, and a geometry well suited for local control of light absorption. Indeed, InAs nanowires with a short InP energy barrier have been observed to produce electric power under global illumination, with an open-circuit voltage exceeding the Shockley-Queisser limit. To understand this behaviour in more detail, it is necessary to establish control over the precise location of electron-hole pair-generation in the nanowire. In this work we perform electron-beam induced current measurements with high spatial resolution, and demonstrate the role of the InP barrier in extracting energetic electrons.We interprete the results in terms of hot-carrier separation, and extract estimates of the hot carriers' mean free path.

Embedded sacrificial AlAs segments in GaAs nanowires for substrate reuse.

We report on the use of a sacrificial AlAs segment to enable substrate reuse for nanowire synthesis. A silicon nitride template was deposited on a p-type GaAs substrate. Then a pattern was transferred to the substrate by nanoimprint lithography and reactive ion etching. Thermal evaporation was used to define Au seed particles. Metalorganic vapour phase epitaxy was used to grow AlAs-GaAs NWs in the vapour-liquid-solid growth mode. The yield of synthesised nanowires, compared to the number expected from the patterned template, was more than 80%. After growth, the nanowires were embedded in a polymer and mechanically removed from the parent substrate. The parent substrate was then immersed in an HCl:H2O (1:1) mixture to dissolve the remaining stub of the sacrificial AlAs segment. The pattern fidelity was preserved after peeling off the nanowires and cleaning, and the semiconductor surface was flat and ready for reuse. Au seed particles were then deposited on the substrate by use of pulse electrodeposition, which was selective to the openings in the growth template, and then nanowires were regrown. The yield of regrowth was less optimal compared to the first growth but the pattern was preserved. Our results show a promising approach to reduce the final cost of III-V nanowire based solar cells.

Operando Surface Characterization of InP Nanowire p-n Junctions.

We present an in-depth analysis of the surface band alignment and local potential distribution of InP nanowires containing a p-n junction using scanning probe and photoelectron microscopy techniques. The depletion region is localized to a 15 nm thin surface region by scanning tunneling spectroscopy and an electronic shift of up to 0.5 eV between the n- and p-doped nanowire segments was observed and confirmed by Kelvin probe force microscopy. Scanning photoelectron microscopy then allowed us to measure the intrinsic chemical shift of the In 3d, In 4d, and P 2p core level spectra along the nanowire and the effect of operating the nanowire diode in forward and reverse bias on these shifts. Thanks to the high-resolution techniques utilized, we observe fluctuations in the potential and chemical energy of the surface along the nanowire in great detail, exposing the sensitive nature of nanodevices to small scale structural variations.

Template-assisted vapour-liquid-solid growth of InP nanowires on (001) InP and Si substrates.

We report on the synthesis of vertical InP nanowire arrays on (001) InP and Si substrates using template-assisted vapour-liquid-solid growth. A thick silicon oxide layer was first deposited on the substrates. The samples were then patterned by electron beam lithography and deep dry etching through the oxide layer down to the substrate surface. Gold seed particles were subsequently deposited in the holes of the pattern by the use of pulse electrodeposition. The subsequent growth of nanowires by the vapour-liquid-solid method was guided towards the [001] direction by the patterned oxide template, and displayed a high growth yield with respect to the array of holes in the template. In order to confirm the versatility and robustness of the process, we have also demonstrated guided growth of InP nanowire p-n junctions and InP/InAs/InP nanowire heterostructures on (001) InP substrates. Our results show a promising route to monolithically integrate III-V nanowire heterostructure devices with commercially viable (001) silicon platforms.

High Responsivity of InP/InAsP Nanowire Array Broadband Photodetectors Enhanced by Optical Gating.

High-performance photodetectors operating in the near-infrared (0.75-1.4 µm) and short-wave infrared (1.4-3.0 µm) portion of the electromagnetic spectrum are key components in many optical systems. Here, we report on a combined experimental and theoretical study of square millimeter array infrared photodetectors comprising 3 million n+-i-n+ InP nanowires grown by MOVPE from periodically ordered Au seed particles. The nominal i-segment, comprising 20 InAs0.40P0.60 quantum discs, was grown by use of an optimized Zn doping to compensate the nonintentional n-doping. The photodetectors exhibit bias- and power-dependent responsivities reaching record-high values of 250 A/W at 980 nm/20 nW and 990 A/W at 532 nm/60 nW, both at 3.5 V bias. Moreover, due to the embedded quantum discs, the photoresponse covers a broad spectral range from about 0.70 to 2.5 eV, in effect outperforming conventional single InGaAs detectors and dual Si/Ge detectors. The high responsivity, and related gain, results from a novel proposed photogating mechanism, induced by the complex charge carrier dynamics involving optical excitation and recombination in the quantum discs and interface traps, which reduces the electron transport barrier between the highly doped n+ contact and the i-segment. The experimental results obtained are in perfect agreement with the proposed theoretical model and represent a significant step forward toward understanding gain in nanoscale photodetectors and realization of commercially viable broadband photon detectors with ultrahigh gain.

Radiation Tolerant Nanowire Array Solar Cells.

Space power systems require photovoltaics that are lightweight, efficient, reliable, and capable of operating for years or decades in space environment. Current solar panels use planar multijunction, III-V based solar cells with very high efficiency, but their specific power (power to weight ratio) is limited by the added mass of radiation shielding (e.g., coverglass) required to protect the cells from the high-energy particle radiation that occurs in space. Here, we demonstrate that III-V nanowire-array solar cells have dramatically superior radiation performance relative to planar solar cell designs and show this for multiple cell geometries and materials, including GaAs and InP. Nanowire cells exhibit damage thresholds ranging from ∼10-40 times higher than planar control solar cells when subjected to irradiation by 100-350 keV protons and 1 MeV electrons. Using Monte Carlo simulations, we show that this improvement is due in part to a reduction in the displacement density within the wires arising from their nanoscale dimensions. Radiation tolerance, combined with the efficient optical absorption and the improving performance of nanowire photovoltaics, indicates that nanowire arrays could provide a pathway to realize high-specific-power, substrate-free, III-V space solar cells with substantially reduced shielding requirements. More broadly, the exceptional reduction in radiation damage suggests that nanowire architectures may be useful in improving the radiation tolerance of other electronic and optoelectronic devices.